RAM M8 Handlebar Clamp Universal Finger-Grip Short Arm Mount Kit

Reviews

Be The First To Review This Product!

Help other PROMOUNT users shop smarter by writing reviews for products you have purchased.

Description

RAM Motorcycle M8 Handlebar Bolt Universal Finger-Grip Short Arm Mount Kit

The RAM-B-367-A-UN4U consists of a M8 bolt base, SHORT double socket arm and universal Finger Grip cradle. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm. This allows for almost infinite adjustment and perfect viewing angles.

The RAM Composite Universal Finger Grip cradle is designed to hold a large amount of cell phones and electronic devices. The cradle comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device.

The fingers open by squeezing the ends to open the small finger arms. The bottom of the cradle includes a back plate that adds support to the device being held by the mount. The spine plate contains the universal AMPS and 38mm x 50mm (1.5" x 2") hole patterns.

Compatible motorcycles:
Any motorcycle which employs an 8mm bolt or smaller on its structure. A smaller bolt can be used, though the load capacity decreases with the bolt size.

Included in this kit:
• 1 x M8 x 55mm bolt (1.25 thread pitch)
• 1 x M8 x 60mm bolt (1.25 thread pitch)
• 1 x M8 x 65mm bolt (1.25 thread pitch)

Attachment Point:
Motorcycle handlebar top clamp, any bike that uses an M8 threaded bolt.

Height Dimensions:
Minimum with Top and Bottom Plates: 133mm (5.25")
Maximum with Top and Bottom Plates: 152mm (6.0")
The top and bottom plates can be removed for larger devices.

Spine Plate Dimensions:
63mm x 127mm (2.5" x 5") Width x Height

Using Short Arm Side Clamps:
Maximum Depth: 19mm (0.75")
Minimum Width: 32mm (1.25")
Maximum Width: 76mm (3.0")

Using Medium Arm Side Clamps:
Maximum Depth: 32mm (1.25")
Minimum Width: 38mm (1.5")
Maximum Width: 89mm (3.5")

Using Long Arm Side Clamps:
Maximum Depth: 40mm (1.6")
Minimum Width: 57mm (2.25")
Maximum Width: 89mm (3.5")

Material:
High Strength Composite and Powder Coated Marine Grade Aluminium

Ball Size:
B Size 1" Rubber Ball

Note:
To determine if these bolts are compatible with your motorcycle measure the original bolt from the motorcycle and add 30mm to the length. If it matches one of the 55, 60, or 65 mm length, then you can use the appropriate bolt supplied with the mount. If it does not match, you may be able to source the correct length of bolt locally from a fastener supplier.

Warranty

RAM Limited Lifetime Warranty

Warranty covers the mount or its components only. The mounted device is not covered under the Lifetime Warranty and will not be replaced if damaged as a result of mount failure.

This warranty is expressly limited to the persons in the United States, and all foreign countries who purchase RAM for resale or use in the ordinary course of the buyer's business.

This warranty does not cover any product or part that has been abused, worn out, heated, ground or otherwise altered, used for a purpose other than that for which it was intended, or used in a manner inconsistent with any instructions regarding its use.

In the unlikely situation that a RAM Mounts product fails due to a manufacturing defect, please contact us to arrange the approved return of the item at your cost.

We will evaluate the issue and either –
1. Repair the item and ship it back to you at our cost
2. Replace the item with an equivalent product and ship it back to you at our cost

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.